What is the difference between the muxponder and transponder systems?
The muxponder systems have an integrated filter for muxing the channels together. The muxponder solutions support point-to-point, linear, or ring topologies. The muxponder systems can be expanded by stacking systems to a maximum of 40 channels, and can mix and match 10G and 100G systems.
The transponder systems do not have an integrated filter, but require an external DMD (Mux/Demux) filter to aggregate the DWDM channels together. The transponder supports ring, linear, point-to-point, and mesh topologies. The transponder solutions can be expanded by stacking systems up to 96 channels, which means 9.6TB on the line-side and 11TB on the client-side. Again, you can have a mix of 10G and 100G systems for each of those 96 channels.
Do I need to open a maintenance window to add clients?
No maintenance window is needed if your XKL network is designed to minimize disruption for future growth. XKL utilizes FlexArc technology that allows you to rack and stack systems without opening a maintenance window if the Mux/Demux (DMD) is installed with the initial installation. After that, additional systems can be added without disruption to existing traffic. If the DMD is NOT installed initially, then a reasonably short maintenance window would be required. Most XKL systems can be installed in under an hour. There will be no interruption of service for existing channels.
Do you have a GUI interface for programming and system management?
XKL has a very simple and intuitive CLI interface, which is designed to support easy configuration. Therefore, you do not have to learn a new management tool to become an expert at provisioning and monitoring. XKL does not currently have a GUI interface (it’s generally not needed by our customers). XKL also has partners with management tools that provide a GUI and the ability to manage numerous vendors from a single tool.
Do you have to be certified by XKL to install, provision, or operate XKL equipment?
No, XKL has removed the complexity from Layer 1 optical networking. XKL systems are designed with router/switch techs in mind and most customers need very little training to comfortably install, provision, monitor and maintain the XKL equipment. XKL provides the training needed for customers, which usually can be performed over a couple of web conference sessions remotely. XKL provides all the clearly laid out connectivity and installation diagrams with the shipped systems.
What kind of power supply options are available?
XKL provides redundant, hot-swappable power supplies. Each system can be equipped with either 2xAC, 2xDC power supplies or 1AC & 1DC power supply.
What type of protection does XKL support?
XKL offers several solutions.
The DMD-A systems, when applied to Point-to-Point or Linear networks, have an optionally integrated optical protection switch (OPS). This OPS allows for a working path and protected path, which is a second fiber pair (usually diverse path) to support continuous operation if a fiber break or other failure on one path were to take place. The OPS will switch the traffic in sub-50ms to the protected path.
The DSM10 systems provide Automatic Path Protection (APP). The APP feature uses the electrical crossbar to automatically switch traffic to a fail-over channel if the connection to the primary channel is interrupted. Optionally, the systems can be set up to fall back to the original channel when the connection is restored. APP can be changed during system operation at any time. APP is soft-configurable on a per-interface basis.
Additional protection schemes are in development for various models. Ask your XKL contact for more information
What is the maximum distance supported without adding in-line amplifiers?
The distance XKL solutions can support with integrated EDFA’s is around 150km, or up to 200km with EFDA/Raman hybrid solution, depending on fiber type, losses in the fiber, and fiber quality.
XKL can integrate amplifiers within either of the systems themselves or within the Mux/Demux (DMD) system itself. Integrating the amplification into the DMD saves costs in the long run as it amplifies for all systems stacked under it (versus integrating amplification into each system).
What is the cost for licensing, warranty and other recurring fees?
XKL does not require any licensing fees at all – no hardware license fees, no software license fees – for the life of the system.
XKL does not charge for software upgrades for the life of the system.
XKL provides the first year of standard warranty on each device FREE (100% discounted). Prices are quoted for Years 2-5 for budgetary planning purposes for both the standard or upgraded warranties. The decision of whether or not to renew the warranty is solely at the customer’s discretion up to 5 years. This helps reduce your overall total cost of ownership.
Does XKL code its lasers?
No, XKL does not code its lasers. That means, in the event of a laser failure, you can utilize quality off-the-shelf lasers to bring your system back up. However, XKL requires that you install an XKL-qualified laser, or an XKL approved third-party laser, in order to maintain your warranty. XKL performs a significant amount of testing on high quality lasers and, upon request once a system is purchased, XKL can provide a qualified list of approved vendors that have met our system performance specifications.
Do you support 100G client side services?
Yes, XKL supports 100G SR10 interfaces on the DSM10, DQT10 and DQM10 products.
100G SR10 support will be available on the DQT100/DQM100 in a future software release. Please consult with your XKL contact about the timing of your project to find out the latest.
100G LR4 is planned for a future product release.
Do you support OTN G.709?
XKL uses G.709 digital wrappers within the coherent 100G product line, eVolocity. However, XKL does not support G.709 switching.